Federal Pacific Panel Replacement in Salem, OR
Federal Pacific Electric (FPE) Stab-Lok panels are known to fail to trip during overload and short-circuit conditions, leaving homes at elevated risk of electrical fire. Wire Smart Inc. replaces FPE Stab-Lok panels in Salem and surrounding Marion / Polk County homes with modern 200A panels — permitted through the Oregon BCD, with utility coordination and inspection included.
Quick Answers
Direct answers for Salem, Marion County, Polk County, and the Willamette Valley.
- Who
- Wire Smart Inc., a Salem-based licensed electrical contractor (Oregon CCB #215974, BCD #C1787) with 25+ years of service-upgrade experience.
- What
- Full Federal Pacific Stab-Lok panel replacement with a modern 200A panel (typically Square D, Eaton, or Siemens), new main breaker, new grounding and bonding, and breaker swap to AFCI/GFCI where required by current code.
- Where
- Salem, Keizer, Dallas, Monmouth, Independence, Silverton, Stayton, and surrounding Marion and Polk County communities.
- How much
- Free estimate. Most Salem FPE-to-200A panel replacements run $2,800–$4,500 depending on meter base condition, grounding upgrades, and required code updates.
- When
- Typically scheduled within 1–2 weeks once the estimate is approved; full panel swap is usually a single-day job.
What We Do
- Remove existing Federal Pacific Stab-Lok panel
- Install new 200A panel (Square D, Eaton, or Siemens)
- Coordinate utility power disconnect / reconnect with PGE or Salem Electric
- Upgrade grounding electrodes and bonding to current code
- Install AFCI / GFCI breakers where required
- Pull permit through Oregon BCD and schedule the state inspector
Common Reasons Customers Call Us
- Identified an FPE Stab-Lok panel during a home inspection
- Insurance carrier flagged the panel and is asking for replacement
- Buying or selling a Salem home with a Federal Pacific panel
- Breakers that won't reset, are warm, or have tripped without resetting properly
- Burning smell, scorch marks, or buzzing at the panel
Our Process
- Step 1On-site inspection — confirm FPE Stab-Lok, scope grounding and meter work.
- Step 2Written estimate with permit, utility, and inspection fees itemized.
- Step 3Schedule the utility disconnect and the state inspector.
- Step 4Single-day swap, labeled circuits, walk-through and inspection.
Why Work With Wire Smart Inc.
- 25+ years of Salem-area service-upgrade experience
- Familiar with PGE and Salem Electric service standards
- Oregon CCB #215974 · BCD #C1787 — licensed and insured
- Permit pulling, utility coordination, and inspection included
Get Federal Pacific Panel Replacement in Your Area
Wire Smart Inc. offers federal pacific panel replacement across the Salem metro and Willamette Valley. Pick the closest area below for local utility, permit, and ZIP-specific details.
Cities We Serve
Salem Neighborhoods
- FPE & Zinsco Panel Replacement in South Salem, Salem
- FPE & Zinsco Panel Replacement in West Salem, Salem
- FPE & Zinsco Panel Replacement in North Salem, Salem
- FPE & Zinsco Panel Replacement in Northeast Salem, Salem
- FPE & Zinsco Panel Replacement in Four Corners, Salem
- FPE & Zinsco Panel Replacement in Northgate, Salem
- FPE & Zinsco Panel Replacement in Sunnyslope, Salem
- FPE & Zinsco Panel Replacement in Morningside, Salem
- FPE & Zinsco Panel Replacement in Englewood, Salem
- FPE & Zinsco Panel Replacement in Faye Wright, Salem
Helpful Guides
Cost ranges, code requirements, and decision guides written for Salem-area homeowners.
Frequently Asked Questions
Why is my Federal Pacific panel considered unsafe?
Federal Pacific Electric (FPE) Stab-Lok breakers have a documented history of failing to trip during overcurrent or short-circuit events. A breaker that doesn't trip when it should can let a circuit overheat, melt wiring insulation, and start a fire. Most insurers and home inspectors flag them and recommend replacement.
How much does it cost to replace a Federal Pacific panel in Salem?
Most Salem-area FPE-to-200A replacements run $2,800–$4,500 depending on meter base condition, grounding upgrades, and any required AFCI/GFCI code updates. We provide a written estimate before any work.
Will the power be off all day?
Power is off only during the actual swap — typically 4–8 hours. We coordinate the utility disconnect/reconnect with PGE or Salem Electric and aim to restore power the same day.
Do I need a permit?
Yes. Panel replacements require an electrical permit through the Oregon Building Codes Division (BCD). We pull the permit and schedule the state inspector — fees are itemized in your estimate.
Related Services
Customers who book federal pacific panel replacement often need these adjacent services on the same job.
Request an Estimate
Call Wire Smart Inc. at 503-383-1602 or send us a message. We respond quickly to homes and businesses across the Salem area.
Back to homepage · Browse all services · Get a free estimate